what bootloader can i used with my STB B860H

[yunuslo]

dear,

i am already try to modify file boot.ini and uEvn.txt with location DTB, still not running boot from SDcard.
used : Armbian_22.02.0_Aml_s905x_focal_5.4.169_2022.01.03.1355.img.gz

i'm already try used replace the bootloader, with HG680p.

information log before i'm replace the bootloader

U-Boot 2015.01-ge1b7b3f-dirty (Aug 24 2017 - 23:11:22)

DRAM: 1 GiB
Relocation Offset is: 3eeaf000

Starting uboot
-----board_version[9]
gpio: pin GPIOAO_6 (gpio 106) value is 1
gpio: pin GPIOCLK_1 (gpio 99) value is 1
gpio: pin GPIOAO_4 (gpio 104) value is 1
gpio: pin GPIOX_15 (gpio 15) value is 1

Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: gxl platform: p215 variant: 1g
dtb 0 soc: gxl plat: p212 vari: 1g
dtb 1 soc: gxl plat: p212 vari: 2g
dtb 2 soc: gxl plat: p215 vari: 1g
Find match dtb: 2

after i'm replace it the file log information not same.

-----board_version[9]
unified board, board id adc = 9
Fiberhome GPIOAO_4 power on!!!!! Multi dtb tool version: v2 .
Support 3 dtbs.
aml_dt soc: gxl platform: p212 variant: 1g
dtb 0 soc: gxl plat: p212 vari: 1g
dtb 1 soc: gxl plat: p212 vari: 2g
dtb 2 soc: gxl plat: p215 vari: 1g
Find match dtb: 0

please help me what bootloader & dtb can i used ?

[ophub]

The B860H box use s905x armbian firmware does not need to modify any information. After decompressing it directly, it can be used after writing into the SD card.

https://github.com/ophub/amlogic-s9xxx-armbian/releases/download/Armbian_Aml_focal_2022.01.03.1400/Armbian_22.02.0_Aml_s905x_focal_5.4.169_2022.01.03.1355.img.gz

https://github.com/ophub/amlogic-s9xxx-armbian/releases/download/Armbian_Aml_bullseye_2022.01.03.1740/Armbian_22.02.0_Aml_s905x_bullseye_5.4.169_2022.01.03.1735.img.gz

[yunuslo]

dear. ophub.

i am already reburn to my SDcard without modify the file and trying to run boot to SDcard. my STB still looping reseting/restart.
i'm used https://github.com/ophub/amlogic-s9xxx-armbian/releases/download/Armbian_Aml_focal_2022.01.03.1400/Armbian_22.02.0_Aml_s905x_focal_5.4.169_2022.01.03.1355.img.gz

log B860H.txt
full log from start android pulpstone and replace the bootloader with HG680p.txt

i'm try re-burn focal to bulleyes, still error and looping
full.log.img bulleye.txt

[ophub]

Wait a moment and it will reload again. It is ready to use after the second start in 10 seconds.

[yunuslo]

Wait a moment and it will reload again. It is ready to use after the second start in 10 seconds.

ok, i will try again with another B860H version, i wish can run

[ophub]

Just now I repackaged the latest version of today, you can download and test it.

[yunuslo]

dear, ophub.

i'm already trying without modify uEvn.txt and boot.ini the result still looping reset/restart.

but after i'm trying modify file boot.ini at "mmc" change to /dtb/amlogic/xxx same location at uEvn.txt, and rename file u-boot-s905x-s912.bin to u-boot.ext armbian starting, but at my monitor looping to and not display clear.

log after modify boot ini.txt
the log look, already starting apps, but the display not clear.

[ophub]

You re-download the firmware you just updated. Don't modify it. It will automatically reload once at startup. You can see the final ip from the router.
SSH to the box from the local area network. Check in the terminal, the ghost of the display screen may be the cause of the display driver.
The configuration of this firmware has been around for a long time, they can use this default dtb file normally.

[ophub]

u-boot.ext will automatically reload once, and it can be used normally after the second boot. Is your box a new variant?

[ophub]

try:
mod uEnv.txt dtb name: meson-gxl-s905x-zte-b860h.dtb
u-boot: u-boot-p212.bin or u-boot-s905x-s912.bin copy to u-boot.ext

[yunuslo]

You re-download the firmware you just updated. Don't modify it. It will automatically reload once at startup. You can see the final ip from the router. SSH to the box from the local area network. Check in the terminal, the ghost of the display screen may be the cause of the display driver. The configuration of this firmware has been around for a long time, they can use this default dtb file normally.

on my router not detect mac address my device

u-boot.ext will automatically reload once, and it can be used normally after the second boot. Is your box a new variant?
i'm not sure what version my board

try: mod uEnv.txt dtb name: meson-gxl-s905x-zte-b860h.dtb u-boot: u-boot-p212.bin or u-boot-s905x-s912.bin copy to u-boot.ext

ok wait i will try it.

[yunuslo]

try: mod uEnv.txt dtb name: meson-gxl-s905x-zte-b860h.dtb u-boot: u-boot-p212.bin or u-boot-s905x-s912.bin copy to u-boot.ext

i already try mod uEnv.txt dtb name meson-gxl-s905x-zte-b860h.dtb and uboot : u-boot-p212.bin the result is loop reset / restart

if i am mod uEnv.txt dtb name meson-gxl-s905x-zte-b860h.dtb and uboot : u-boot-s905x-s912.bin the result is starting but at my display looping same with the image display my monitor.

i think my device is dtb 2 soc: gxl plat: p215 vari: 1g if i check the log if i'm running android pulpstone Pulpstone_ZTE_B860H_Flasher_Tool_v3.4.exe

i am already try to used source dtb at https://github.com/ndunks/custom-rom-stb-zte-B860-indihome/tree/master/dtb the result run the apps but not start armbian.

and i already try img from armbian[dot]com > Armbian_20.10_Arm-64_buster_current_5.9.0.img.xz the result is running but can't install on mmc just run on SDcard

i will try another time used img from ophub, maybe i must find another board series B860H.
and i very appriciate your response & help. ophub

[ophub]

Which dtb and u-boot file are you using in Armbian_20.10_Arm-64_buster_current_5.9.0.img.xz?
You try to modify the firmware of ophub to the same value. Try it

[aipmy]

solved?

[ophub]

meson-gxl-s905x-p212.dtb
u-boot-p212.bin

I consulted the user of this device again. He has two devices, B860H and HG680-P, and they use the same firmware. The OpenWrt he used was confirmed to be usable. Armbian and OpenWrt are the same. Yes offcourse, 5.4.xx, 5.10.xxx, 5.15.xxx Support. The following device pictures and software interface were sent to me after he just tested it.