Issue with Logo Overlay

[ChuckIn85085]

Good afternoon, all.

I am having one HELL of an issue getting a Logo Overlay to burn in on my recordings. I have done everything the Labs page says, as well as asking the ChatGPT Labs UI to assist, and nothing..

Here is my combined code for a Hero10 Black:
MBOOT="!LRoxy"!SAVERoxy=!SA7D2H5!RLOGO="RoxyLogo.png"BRNX=30,30BRNP=BR

Now before people tell me it's the code, I have also tried splitting the code.
*MBOOT="!LRoxy"!SAVERoxy=!SA7D2H5!R Seperate of: *LOGO="RoxyLogo.png"BRNX=30,30BRNP=BR

The GPT is the one that helped make sure the code I have to combine the two is correct. I have a * where I should have had a ! on the MBOOT, and she corrected me on that - lol

The Transparent PNG file is 250 x 60 and located in the MISC folder. I also tried doing as the labs page suggests and right-click the GoPro logo file, and that also doesn't show, no matter if I use the suggested code and scanning the QR code on that Overlay generator QR page, or if I use the GPT information.

Thanks everyone!

[dnewman-gpsw]

Sorry the AI hallucinations to produce this nonsense. Better to read the docs.

Only import thing: what camera model?

[ChuckIn85085]

Hero 10 Black.

I could have swore I put that. My apologies!!

[dnewman-gpsw]

HERO10, like all GP2 camera are limited to overlays running in 4k 16x9 at 30 fps or lower. So try the basics first. Follow the instructions from here https://gopro.github.io/labs/control/logo/

[ChuckIn85085]

*MBOOT="!LRoxy"!SAVERoxy=!SG6D2H5!R*LOGO="roxylogo.png"*BRNX=20,20*BRNP="BR"

That command will not work, logically if will never get to *LOGO.

Don't mix permanent command with boot scripts. There are too very different operations. You where saving *LOGO... into the Roxy file, and and is was after !R is was never run. If you want have a single QR Code, the correct order will help.

*LOGO="roxylogo.png"*BRNX=20,20*BRNP="BR"*MBOOT="!LRoxy"!SAVERoxy=!SG6D2H5!R

So no matter what I do, when I power off the camera, the logo is gone from new recordings. Everything else is there and works as it should.

I can rescan a QR code and it's back again. Isn't this supposed to be a permanent available option with the *LOGO command?

When I power on, I see this order of presedence:

Owner Information

next page
Features activated:
24HZ, 64BT, FSOS, TUSB, BRNX=20,
BRNP, LOGO, QRDR, BOOT

next page
Boot Command:
!LRoxy

next page

At this point, it then starts counting down the to load the Boot Command. So is the boot command wiping out the logo command? I wouldn't think so, since that acknowledgement screen shows it's there, etc.

I guess I'm just not going to get a logo!? :-(

[dnewman-gpsw]

You should not have "FSOS" as a permanent abled feature. Scan *FSOS=0. It is not your issue, but that one is not good to have on all the time, that can slow booting a lot.

This is a typo in the command, should be (sorry I didn't catch that earlier):

*BOOT="!LRoxy"!SAVERoxy=!SG6D2H5!2N!R

Not *MBOOT, as that is mixing, old and new command styles. I added the !2N as that help HERO13 users.

All works for me.

[ChuckIn85085]

I went ahead and made some changes to my stuff. Every time you suggest something for me, I always do a !RESET!1OR and a !FORMAT to make sure everything is back to scratch.

I then copy the roxylogo.png file to the MISC folder and verify that is the only file on the SDCard with the exception of the internal format command.

After that, I did the following using the GoPro Labs QR Code Generator Page:

!M24HZ=1
!M64BT=1
!MTUSB=1

Then, I utilized the code you tweaked and verified for the boot loading and logo impression:

*LOGO="roxylogo.png"BRNX=20,20BRNP="BR"*BOOT="!LRoxy"!SAVERoxy=!SI6D3H5!2N!R

Notice I didn't put any "Owner Info" on there this time. Just figured that's not really needed at this point.

So same thing.. I recorded three separate videos utilizing the trigger. Those three also had the logo in the bottom right corner.

I powered off the GoPro and waited about 30 seconds to power back on.

I recorded three separate videos utilizing the trigger. However this time, there is no logo on the bottom right corner.

So seems like maybe I need to rescan the QRCode for the boot and/or Logo each time the H10 is powered on?

[dnewman-gpsw]

Maybe it is just your HERO10, but I still expect it more like something unexpected that you are doing, as there has never been a true, "only on my camera". I can't get it to fail even once.

This is the metadata from one of my captures (with working logos):

[ChuckIn85085]

yeah, with my luck it's just my camera.

I did the exact steps I did the other day and once again, the videos recorded during the session where the QR codes are sent to the camera, everything works perfectly fine.

Once I reboot the camera (simply hold the power button, wait a few seconds, then power back on. Or, use the Qlik app to power off and on), the logo doesn't record on the bottom right.

Here's a copy of my MetaData as well. I noticed I don't have any of the "0"'s that you do, but we both have the "1"'s and the logo file listed:

I mean hell - it seems my camera keeps draining the battery even when powered off. I went to turn it on today and it wouldn't power on until I changed the battery. When I put the battery that was in the H10 in the charger, it showed it still had 23% remaining.

So I don't know... If my camera just is not wanting to cooperate or what. If I can't get the logo to stay on there, then so be it. My main thing is the start and stop of the trigger, which I need to turn the sensitivity down even more at this point, because six is too sensitive and records when the buggy is simply idling and not just moving.